SSAB builds the range across minimum yield strengths from 650 MPa upward, and the series a designer picks changes plate thickness, structure weight and the fabrication route. Cranes and loaders work their steel hard. Booms carry bending loads over long spans, loader arms absorb shock each time the bucket hits the pile, and chassis members cycle through load reversals for years. Choosing Strenx steel for cranes and loaders starts with the design calculation and the duty cycle.
Why Is Strenx Steel Used in Cranes and Loaders?
Designers specify Strenx to hold a required section strength at reduced plate thickness. Thinner plate carries less dead weight. A boom rolled from 960 MPa plate resists the same calculated bending moment as a much thicker low-strength section, which frees payload budget and cuts counterweight. Crane booms, telescopic sections, loader arms, lifting lugs, outrigger beams and chassis rails all accept these grades once the designer verifies the choice against the drawing. Performance comes from the full package: section geometry, weld procedure, grade and service loads. Changing plate grade alone does not raise rated lifting capacity, since that figure follows structural design, stability limits and the certification standard.
Which Strenx Steel Grades Are Suitable for Cranes and Loaders?
Three series cover most crane and loader work: Strenx 700, 900 and 960. Each groups several grades with different product forms, thickness bands and toughness classes.
Strenx 700 Series
Strenx 700 guarantees 650 to 700 MPa minimum yield, depending on thickness. Strenx 700 E/F runs 4.0 to 160.0 mm as plate, reaching heavy chassis members and boom foot sections, while cold-rolled and hot-rolled strip forms start at 0.7 mm.
Strenx 900 Series
Holding 830 to 900 MPa minimum yield, Strenx 900 serves lifting and transportation structures. Strenx 900 E/F covers 4.0 to 120.0 mm plate, 900MC runs 3.0 to 10.0 mm, and 900 Plus sheet spans 2.0 to 8.0 mm. Match the toughness class to design temperature.
Strenx 960 Series
Strenx 960 reaches 850 to 960 MPa minimum yield and suits long booms where every kilogram of dead weight costs reach. Strenx 960 Plus guarantees 30 J at minus 40 degrees Celsius. Higher yield still does not win every time, because slender sections buckle before they yield.
Strenx 700 vs 900 vs 960: How Do You Choose?
- Strength level: Minimum yield rises from 650 MPa in the 700 group to 960 MPa, subject to grade and thickness.
- Typical consideration: Weigh the strength gain against tighter bending radii, preheat rules and matching weld consumables.
- Selection priority: Decide whether the component needs moderate, high or very high strength for its calculated stress.
| Series | Minimum yield strength | Typical consideration | Selection priority |
| Strenx 700 | 650 to 700 MPa | Widest thickness range, simplest fabrication | Moderate strength, heavy sections |
| Strenx 900 | 830 to 900 MPa | Strength and workshop properties balanced | High strength, lifting structures |
| Strenx 960 | 850 to 960 MPa | Tighter limits on forming and welding | Very high strength, weight-critical designs |
Figures follow the SSAB Strenx product offer. Read the individual datasheet, since each series spans several grades and forms.
Key Factors When Selecting Strenx Steel for Cranes and Loaders
- Load requirements: Check rated loads, dynamic amplification, fatigue classes and the design standard the machine must satisfy.
- Component design: Tie the grade to the part, whether boom, arm, chassis or lifting attachment.
- Thickness and product form: Confirm plate, strip or tube availability against the drawing thickness.
- Welding and fabrication: Follow grade-specific guidance on cutting, cold forming, preheat and consumable selection.
- Operating environment: Account for service temperature, impact toughness, abrasion and corrosion exposure.
Your equipment designer or a qualified structural engineer signs off on the final grade.
Explore Strenx Steel Products from Kamlesh Metal Alloy
Kamlesh Metal & Alloy has traded in steel since 1970 and handles Strenx 700, 900, 960 and 1100 from SSAB Sweden. Buyers comparing options can review the Strenx Steel Products from Kamlesh Metal Alloy listing, then send the drawing to confirm available grades, dimensions, thicknesses, product forms, and test documentation.
Conclusion
Strenx 700, 900 and 960 each fit different crane and loader designs. A 160 mm chassis plate and a 3 mm telescopic section do not call for the same grade, and a machine running at minus 30 degrees Celsius does not match one in a Mumbai yard. The right Strenx steel for cranes and loaders comes from calculated strength, component geometry, fabrication method and operating conditions together.
Browse the Strenx range at Kamlesh Metal & Alloy and send your drawing for a grade-wise quote.